TE Opaque LSAs are generated in this area. The area used for MPLS traffic engineering. Name of the routing filter chain used for incoming prefixes Needed for interoperability with older Cisco systems. If set, then used in route redistribution (as route-tag in all external LSAs generated by this router), and in route calculation (all external LSAs having this route tag are ignored). By default Null domain-id is used, as described in RFC 4577. This value is attached to OSPF routes redistributed in BGP as VPNv4 routes as BGP extended community attribute and used when BGP VPNv4 routes are redistributed back OSPF to determine whether to generate inter-area or AS-external LSA for that route. To start OSPF v2 and v3 instances, the first thing to do is to add the instance and the backbone area: RFC 7471 - OSPF Traffic Engineering (TE) Metric Extensions.RFC 6845 - OSPF Hybrid Broadcast and Point-to-Multipoint Interface Type.RFC 6565 - OSPFv3 as a Provider Edge to Customer Edge (PE-CE) Routing Protocol.RFC 6549 - OSPFv2 Multi-Instance Extensions.RFC 5643 - Management Information Base for OSPFv3.RFC 5329 - Traffic Engineering Extensions to OSPF Version 3.RFC 4577 - OSPF as the Provider/Customer Edge Protocol for BGP/MPLS IP Virtual Private Networks (VPNs).RFC 3630 - Traffic Engineering (TE) Extensions to OSPF Version 2.RFC 3101 - The OSPF Not-So-Stubby Area (NSSA) Option.It always chooses the shortest path to the subnetwork first. The OSPF protocol is the link-state protocol that takes care of the routes in the dynamic network structure that can employ different paths to its subnetworks.

802.MikroTik RouterOS implements OSPF version 2 (RFC 2328).

EAPoL (Extensible Authentication Protocol over LAN).

Authentication, Authorization, Accounting.

GRE Tunnel Configuration with Cisco Packet Tracer.

Local SPAN Configuration on Packet Tracer.

Remote SPAN Configuration on Packet Tracer.

VRRP (Virtual Router Redundancy Protocol).

VLAN Configuration on Cisco Packet Tracer.

VLAN Port Assignment and VLAN Port Types.

Inter VLAN Routing with Router on Stick Topology.

Inter VLAN Routing Configuration Example.

Inter VLAN Routing Configuration on GNS3.

STP Configuration on Cisco Packet Tracer.

RSTP Configuration on Cisco Packet Tracer.

STP Portfast Configuration on Cisco Packet Tracer.

PVST+ and Rapid PVST+Configuration on Packet Tracer.

Basic Cisco Router Security Configuration.

Standard ACL Configuration With Packet Tracer.

Access Control Lists for Traffic Control.

Dynamic NAT Configuration with Packet Tracer.

Static NAT Configuration with Packet Tracer.

Etherchannel Cisco PAgP Configuration on GNS3.

Cisco DHCP Relay Agent Configuration with GNS3.

Point-to-Point Protocol over Ethernet (PPPoE).

Frame Relay Point-to-Point Configuration.

Frame-Relay Configuration with both Inverse-ARP and Frame-Relay Map.

BGP Configuration Example on Packet Tracer.

Cisco BGP Route Reflector Configuration on GNS3.

OSPF(Open Shortest Path First) Overview.

OSPFv3 (Open Shortest Path First Version 3).

OSPFv3 Configuration Example on Cisco IOS.

OSPF Standard Area and Backbone Area on Cisco Packet Tracer.

OSPF External Routes on Cisco Packet Tracer.

OSPF Stub Area and Totally-Stub Area on Cisco Packet Tracer.

OSPF NSSA and Totally NSSA on Cisco Packet Tracer.

EIGRP For IPv6 Configuration On Cisco IOS.

EIGRP (Enhanced Interior Gateway Routing Protocol).

RIPng Configuration Example on Cisco IOS.

Static Route Configuration on Cisco Routers.

ICMP (Internet Control Message Protocol).

To do this configuration, we can use the below command: In other words, the destintion and the next hop addresses are IPv6 addresses in IPv6 static routing configuration.ДЇor example, letвЂ™s do an IPv6 static route configuration example with 2001:ABC::/32 network and 2001:ABC:1111:2222::1 next hop adres. Here, the only difference is using IPv6 addresses. If you would like to test your IPv6 knowledge, you can do this on IPv6 Quizes PageДЄs IPv4 static routes, we can also use static routes for IPv6 addresses. To define a IPv6 Static Route, we will firstly write the prefix OR the network we will reach and then, the next hop to reach that network. In IPv6 Technology, to do this we will use IPv6 Static Routes. Or, in large networks some small amout of routing is done via static routing. This is done when we do not want to use Routing Protocols for small part of a network. IPv6 Static Route Configuration on Cisco IOSДЄs you know, Static Route is the route that you manually define on a router. IPv6 Default Route Configuration on Cisco IOS.IPv6 Static Route Configuration on Cisco IOS.

Summary route calculator ipv6